2001 Bavaria 47 Cruiser structural grid - bonded or glassed?

Started by UP, November 13 2026, 03:24

Previous topic - Next topic

UP

Hi,

I have a Bavaria 47 Cruiser from 2001. When I physically look into my structural grid profiles via the limber holes, I see a bonded joint - an adhesive "poop" can be seen running along the horizontal-vertical joint. However on the outside of the very same grid member, there is considerable glass fiber laid, almost looking as if the lateral grid profiles were first bonded to the hull and then glassed over. Does anybody know details about this construction? Thanks!

Yngmar

That generation was glassed and what you're seeing is probably the other side of the thickened resin fillet that goes before tabbing them together so there isn't a sharp crease.
formerly Songbird - Bavaria 40 Ocean (2001) -- now gone farming

UP

Thanks Yngmar!

I'm having an issue with water ingress during upwind beating when the boat is heeled over, trying to find the leak source. I'm a bit baffled presently, as there is no leak when the boat is dockside or sailing downwind. The hull and deck joint has been completely glassed shut and I just completed a toerail spray test. I found a similar issue posted on SailboatOwners forum for a 2001 Bavaria 47. I'm considering having the keel rebedded, but I have no concrete evidence for the source of the leak. No large cracking around the grid, some gelcoat here-there. Thinking about siphoning.

sy_Anniina

Quote from: UP on November 13 2026, 14:42I'm having an issue with water ingress during upwind beating when the boat is heeled over, trying to find the leak source. I'm a bit baffled presently, as there is no leak when the boat is dockside or sailing downwind...

I had a similar issue, and found the culprit only on a bit heavier weather. In my case the bottom of the anchor locker had slight leak to forepeak under the bunk. Or more accrately The locker bottom to hull joint around locker drain hole was leaking.

Eventually all the water will end at the lowest point.

BR

Tommi
sy Anniina

UP

Tommi, that is a good tip, thanks. Unfortunately for me, I replaced part of the forepeak stowage room bulkhead on my boat, glassed and reinforced it all and made the chamber nice and waterproof, including bulkhead fittings (used Truedesign ones, they are used for filling the two forward water tanks in my boat).

I hope this is something siphoning into the boat, not the keel bolts.

Yngmar

You can build a dam around the keelbolts and go sail. Bluetack or butyl tape should do. Then you can tell if the water comes out of the keelbolts or not.

However, from all my years of Bavaria forum experience, the keelbolts are never the culprit when there are leaks  :))
formerly Songbird - Bavaria 40 Ocean (2001) -- now gone farming

UP

Yngmar, that is my plan. I bought sewage pipe couplers, will glue those over the bolts with Sikaflex. Also will dive under the boat tomorrow to investigate the joint.

sean c

Have a look in the stern of the boat for leaks at the hull and deck joint. It is below the waterline when heeled over. It is glued and screwed and has a plastic bumper on the outside concealing any damage.
Bumping the dock with the stern of the boat can cause cracks in the joint which will leak when heeled.
Ask me how I know. 
See video of yacht construction on link below.
Sean

https://www.youtube.com/watch?v=GIciQXXkd4Q

UP

sean c - that is an interesting proposal, will do. My hull and deck joint have been permanently glassed shut as a fix to the deck-hull sealant failing. But I'll get my torch and check the transom out.

elias

Hi , I m having similar issues with water in the bilges after excessive washing or sailing with lots of spray . Some of my stanchions are a bit wobbly so I suspect them , but last night I put around 5 litres of water in the shower drain area just to reach the level of where the circular teak sits . 2 litres where missing this morning .
As I mentioned could be multiple sources .
I have a question also , the grid that the water travels inside and comes out from the holes at the bilges , where does communicate with the ingress ? It looks sealed in the pictures ?

UP

@elias, what boat do you have?

Some of the structural beams will be closed, some will have limber holes in them. It does not really look like a well thought out system, I might be wrong.

Several sources seem realistic too, yes.

@sean c - I checked my transom joint from the inside, all good, no cracking whatsoever.

elias

Bavaria 50 2007,
I can't understand in which part of the grid water can enter . A friend with Bavaria 46 2006 had water ingress from the plastic rail where the sprayhood slides in and secures on the deck

UP

I'd figure water can enter those grid members which have a limber hole in them.